Home >> Security & Surveillance >> Home Alarm >> Zrabra 100m Wireless Remote Control Transmitter Head Board Module KL-200

Zrabra 100m Wireless Remote Control Transmitter Head Board Module KL-200

SKU:A1485000GA

What a value! You are viewing a 100m Wireless Remote Control Transmitter Head Module!This Transmitter Head Module is widely used for data transmitting and signal control and are specified as preferred components in remote control garage, roller ...
Retail Price:
USD$ 7.98
Wholesale Price:
 
Wholesale Price
Quantity 2-78-1920-49≥50
Price USD$ 4.84USD$ 4.38USD$ 3.91USD$ 3.29
 
Frequency::
Qty:
pieces
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
 
  • Overview

Specifications:


  • Operating Voltage: DC4-12V
  • Operating Current: 10mA
  • Operating Frequency: 266-433MHZ
  • Transmitting Distance: 100M
  • Encoding Type: Fixed code / rolling code
  • Encoding: Short-circuit fast
  • Size: 41 x 20 x 9mm /  x 1.18 x 0.47in

Features:


  • This Transmitter Head Module is designed with a high-security & large memory capacity
  • This Transmitter Head Module is also stable performance & low power consumption
  • This Transmitter Head Module is convenient for customers to use and the material is good

Details:

Zrabra 100m Wireless Remote Control Transmitter Head Board Module KL-200


  • This Transmitter Head Module is widely used for data transmitting and signal control

Zrabra 100m Wireless Remote Control Transmitter Head Board Module KL-200


  • The perfect Wireless Control Switch Board to transmit on / off signals to remote control devices such as props, fog machines, lights, remotely

Zrabra 100m Wireless Remote Control Transmitter Head Board Module KL-200


  • Compact size and low power consumption electronics make this Wireless Remote Control Switch Board a perfect choice for many projects

How to Build a Wireless Remote Control


  • Simple wireless devices use various components to activate an infra-red signal that broadcasts to a receiver box, allowing the user to program the control. Basic wireless remote controls simply turn a device on or off. Components used in a wireless device can be found at most electronics outlets and hobby shops. Specialized retail establishments have pre-packaged kits that can be used by a beginner. At the very least, even experienced electronics enthusiasts use pre-made remote control boxes due to the simplicity of their design, including ergonomic support. The structure of the wireless remote control provides a builder with not only knowledge but the reasons a receiver can be controlled by the device

Instructions:


  • Open the remote control housing and place a push button switch on the side. In the upper right corner of the housing, fasten a 3-volt battery holder. Be sure enough room is available to install and remove the battery
  • Run a wire from the push button switch and link to the 3-volt battery holder at the negative connection. Attach another wire to the push button switch and lead it to the Meg 1/4W resistor and the NPN silicon transistor. Run a third wire from the Meg 1/4W resistor and attach it to the 22K 1/4W resistor and and the PNP silicon transistor
  • Position the infra-red LED on the front of the housing. Attach the LED and run wires to both transistors. From the 22K 1/4W resistor, run a wire to the C220.01uF 16v ceramic disk capacitor. Run another wire between the NPN silicon transistor and the ceramic disk capacitor
  • From the positive connector on the 3-volt battery holder, connect a wire to the PNP silicon transistor. This will allow for proper current flow in a closed circuit. Ensure the push button switch is positioned to "off" and place a 3-volt battery into the holder. Close the remote control housing
  • Point the remote control at a receiver, making sure the LED on the control is aimed at the LED of the receiver. Push the button and the receiver should power on and off. To adjust the receiver to be programmed, point the remote control and hold down the push button switch. Adjust the pot or taper on the receiver

Package Included:


  • 1 x Transmitter Head Module