Home >> Car & Motorcycle Accessories >> Car Parts >> Morpin 2.5" TFT LCD Car Rear View Monitor & 1/3" Color CMOS 420TVL Camera EP-125

Morpin 2.5" TFT LCD Car Rear View Monitor & 1/3" Color CMOS 420TVL Camera EP-125


As a matter of fact that the rear view monitor did help you a lot while driving, but trunks and rear decks often limit the view of the road far away behind the vehicle. This 2.5Inch car rear view monitor with 420TVL EP-125 camera ...
Retail Price:
USD$ 109.98
Wholesale Price:
Wholesale Price
Quantity 2-56-1415-39≥40
Price USD$ 39.24USD$ 38.32USD$ 37.39USD$ 36.15
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
  • Overview



  • Ratio: 4:3 TFT screen
  • Resolution (H x V): 112 x 320 pixels
  • Video Input Signal: 1.0Vpp, composite
  • Power Consumption: 4.75W
  • Power Input: DC 12V


  • Image device: 1/3 inch color CMOS OV7949
  • TV System: PAL/NTSC
  • Effective Pixels: 628 x 582 pixels/510 x 492 pixels
  • Sensing Area: 5.78mm x 4.19mm/4.69mm x 3.54mm
  • Sync System: Internal
  • Resolution: 420TV lines
  • Minimum Illumination: 3Lux/F1.2 (0 Lux when infrared LED on)
  • Lens: 3.6mm/92deg
  • Night Vision Range: 6m/19.7ft
  • S/N Ratio: More than 48db
  • Electronic Shutter: 1/60 - 1/15, 000 seconds
  • Video Output: RCA connector, 1.0vp-p, 750hm
  • Current Consumption: 130mA
  • Power Supply: 12V DC
  • Operation Temperature: -20°C ~ +50°C, RH95% MAX
  • Storage Temperature: -30°C ~ +60°C, RH95% MAX 
  • Other Item: Automatic white balance, AGC and BLC
  • Size: 26 x 38mm/1.0 x 1.5in (Dia. x L)


  • The 2.5inch rear view monitor will provide you with high definition images
  •  The rear view monitor detects when you back up and shows the camera on screen
  • When you put your car in driving, the image disappears and your rear view system becomes a mirror
  • This car rear view monitor is perfect for backing into tight lots or moving in reverse when visibility is limited, just like having an extra eye
  • The rear view camera can get you specific information to the rear view monitor
  • Automatically shift back-view system when reversing the car
  • This is a must-have for any car owners
  • LCD car monitor has automatically turning system


Morpin 2.5

  • 2.5inch LCD Car Rearview Mirror Monitor. You can view the back with it when driving

Morpin 2.5

  • The accessories of the set. The LCD car monitor can be installed easily

Morpin 2.5

Morpin 2.5

  • You can install the monitor on this stand like this picture. Then you can wacth the display conveniently

Morpin 2.5

  • With the high definition camera, you can use the set more vividly

Morpin 2.5

Morpin 2.5

  • With the cords, you can install the rear view monitor quickly and correctly

How to Install a Rear-View Camera in Your Car:

Morpin 2.5

Rear-view cameras are especially useful in tight parking lots, dark areas or in places where children might be running around. You can install as many of these cameras as you want, though one or two is usually enough


  • Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
  • Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
  • Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
  • Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
  • Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
  • Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
  • Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you

Tips & Warnings:

  • Don't rely solely on the rear-view camera when backing up. Use it as a supplementary aid
  • You must have the rear-view monitor set up and installed correctly to receive the video signal from the rear-view camera
  • Don't install the camera (or any electrical device) with the battery connected, or you'll risk a severe electric shock

How to Install a Rear-View Camera in Your Car:

Morpin 2.5

  • Remove the plastic or carpet panel on the inside of the trunk behind the license plate and below the trunk lid. If your vehicle is an SUV (sport utility vehicle) or something similar, expose the innards inside the tailgate
  • Mount the camera. Remove the two license plate bolts and insert them through the camera bolt holes and back onto the car. Use the license plate light hole to push the wiring through to the trunk
  • Run the red and white cable from the camera you have mounted on the license plate frame to a reversing light housing inside the vehicle. The license plate light can provide a convenient hole, or simply drill a new hole and weatherize it with a grommet
  • Trim and strip 1/4 inch of plastic sheathing off the end of the wire at the reversing light housing
  • Identify the vehicle wires that provide power to the reversing lights. Identify them by tracing the wiring back from the reversing light bulb connector. Strip 1/4- inch of plastic sheathing off the wire. This should be at a convenient, easy to reach location--the middle is fine. Wrap the camera wires around the reversing light wires, match red to red and black to black. Seal with electrical tape
  • Attach the display monitor to a convenient position on the dashboard. Use the included hook and loop tape. Plug the power supply from the display monitor into the cigarette lighter plug on the vehicle's dashboard
  • Test and then replace the plastic or carpet panel

Package Included:

  • 1 x Monitor
  • 1 x Camera
  • 1 x Video Cable
  • 2 x Video Extension Cables
  • 1 x Power Extension Cable