Home >> Car & Motorcycle Accessories >> Car Parts >> CarJoy 3.0" TFT Screen Car Rear View Monitor & 1/3" Color CMOS 420TVL AC-29L Camera EP-130

CarJoy 3.0" TFT Screen Car Rear View Monitor & 1/3" Color CMOS 420TVL AC-29L Camera EP-130


This is a handy, light weight RPAS. Non radiation. A must-have item for your car. The reflection is low. Avoid injury to a family member or pet, and even damage to your vehicle, with this safety-first convenience product. Take it home now! You will ...
Retail Price:
USD$ 117.38
Wholesale Price:
Wholesale Price
Quantity 2-56-1415-39≥40
Price USD$ 68.66USD$ 58.23USD$ 47.81USD$ 33.91
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
  • Overview



  • Ratio: 4:3 TFT screen
  • Resolution: 112, 320 pixels (H x V)
  • Video Input Signal: 1.0Vp-p, composite
  • Power Input: DC 12V
  • Power Consumption: 4.75W
  • RCA Video Input
  • Speaker Built-in
  • Non  radiation
  • NTSC/PAL system
  • High luminance
  • Low reflection
  • Handy, light weight, and provide a sharp color image


  • Image device: 1/3 inch color CMOS OV7949
  • TV System: PAL/NTSC
  • Effective Pixels: 628 x 582 pixels/510 x 492 pixels
  • Sensing Area: 5.78mm x 4.19mm/4.69mm x 3.54mm
  • Sync System: Internal
  • Resolution: 420TV lines
  • Minimum Illumination: 3Lux/F1.2 (0 Lux when infrared LED on)
  • Lens: 3.6mm/92deg
  • Night Vision Range: 6m
  • S/N Ratio: More than 48db
  • Electronic Shutter: 1/60 - 1/15, 000 seconds
  • Video Output: RCA connector, 1.0vp-p, 750hm
  • Current Consumption: 130mA
  • Power Supply: 12V DC
  • Operation Temperature: -20 to 50 degrees centigrade, RH95% MAX
  • Storage Temperature: -30 to 60 degrees centigrade, RH95% MAX
  • Other Item: Automatic white balance, AGC and BLC
  • Size: 26 x 38mm/1.02 x 1.50 in


CarJoy 3.0

  • This desige of Car Reariew Monitor is stylish and delicate 

CarJoy 3.0

  • Full-scaled enhanced signal reception

CarJoy 3.0

  • Provide all the cable which you need

How to Install a Rearview Mirror Monitor in Your Car:

  • Disconnect the battery cables from the battery before beginning installation. Use a wrench or socket to remove the battery cables. Check the vehicle's repair guide for the proper wrench or socket size.
  • Remove the original rearview mirror from your car. Leave its mounting bracket on the windshield-you'll attach the rearview mirror monitor to this. Check the rearview mirror's mounting screw to see what size screwdriver you'll need
  • Insert the rearview mirror monitor into the existing mounting bracket on your windshield. Use the bolt supplied with the monitor to secure the device in the mounting bracket
  • Route an A/V power cable from the A/V selector box to the monitor. Connect the A/V cable from the monitor to the A/V power cable. Use cable ties to secure the cables and prevent them from hanging
  • Reconnect the battery. Start your vehicle and select the rearview mirror monitor on the A/V selector box. The video monitor should come on if the rearview mirror monitor is correctly installed

How to Install a Camera in Your Car:

  • Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
  • Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
  • Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
  • Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
  • Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
  • Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
  • Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you

Package Included:

  • 1 x Monitor
  • 1 x Camera
  • 1 x Video Extension Cable
  • 1 x Video Cable
  • 1 x Power Extension Cable
  • 1 x RCA Cable