- Image Sensor: OV 7949 1/3in color CMOS
- TV System: PAL/NTSC
- Total Pixels: PAL: 628 x 586 NTSC: 510 x 496
- Resolution: 420 TVL
- Minimum Illumination: 0.1Lux(IRON)
- Video Output: 1.0Vp-p into 75Ohm
- Power Supply: DC12V ≤ 130mA(IR ON)
- Operating Temperature: -20°C°~ +70°C
- Elegant LCD rear view mirror features manual button touch function
- Purpose monitor and vehicle entertainment
- 3.5in rear view mirror with TFT color LCD, Integrated Bluetooth® for hands-free wireless calls, View incoming calls with built-in caller ID
- Slot device simplifies installation and detachment
- The LCD Rear View Mirror clips to your rear view mirror
- The LCD Rear View Mirror detects when you back up and shows the camera on screen
- When you put your car back in drive, the image disappears and your mirror becomes a mirror again
- This Car Rearview Mirror Monitor is perfect for backing into tight spots or moving in reverse when visibility is limited its like having an extra eye
- Just add video to your vehicle with car rear view system
- Well packed 3.5" TFT Screen Car Rear View Monitor with 1/3" CMOS Camera
- Elegant LCD rear view mirror has digital 3.5Inch TFT LCD display with fine and crisp picture. Add video to your vehicle with a rear view mirror monitor and rear-view camera
- It is an accessory that takes your vehicle to the next level. A very good Car Rearview Mirror Monitor has ultra broad-angle digital TFT-LCD TV, digital photo frame
- This Car Rear View System is easy installation and simple to use. TV technical design shows exquisite & clear image and no radiation
- Avoid injury to a family member or pet, and even damage to your vehicle, with this safety-first convenience product
- Connect the yellow video jack vith monitor video input jack
- Conenct the red (or black) power input jack with power supply
- Recommend using regulated DC12V power supply unit with camera for best picture and for safe operation of the unit
- Do not cut power input jack and connect the conductor to power supply directly, bacause that will fatally injured the camera
- Do not attempt to disassemble the camera. There are no user serviveable parts inside. Refer servivcing to qualified service person
How to Install a Rearview Mirror Monitor in Your Car:
- Disconnect the battery cables from the battery before beginning installation. Use a wrench or socket to remove the battery cables. Check the vehicle's repair guide for the proper wrench or socket size.
- Remove the original rearview mirror from your car. Leave its mounting bracket on the windshield-you'll attach the rearview mirror monitor to this. Check the rearview mirror's mounting screw to see what size screwdriver you'll need.
- Insert the rearview mirror monitor into the existing mounting bracket on your windshield. Use the bolt supplied with the monitor to secure the device in the mounting bracket.
- Route an A/V power cable from the A/V selector box to the monitor. Connect the A/V cable from the monitor to the A/V power cable. Use cable ties to secure the cables and prevent them from hanging.
- Reconnect the battery. Start your vehicle and select the rearview mirror monitor on the A/V selector box. The video monitor should come on if the rearview mirror monitor is correctly installed.
How to Install a Rear-View Camera in Your Car:
- Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts.
- Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal.
- Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out.
- Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight.
- Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse.
- Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions.
- Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you.
- 1 x Car Rear View Monitor
- 1 x Video Output Cable
- 2 x Connecting Cable
- 1 x Camera
- 1 x Manual