Home >> Security & Surveillance >> Home Alarm >> Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000

Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000

SKU:A1485000BI

Practical and reliable, this 3000M Wireless Remote Control Transmitter Board Module XYF-3000 provides you great performance!The wireless transmitter module is crafted from high quality materials, durable and reliable for long time use. Adopt advanced...
Retail Price:
USD$ 12.71
Wholesale Price:
 
Wholesale Price
Quantity 2-78-1920-49≥50
Price USD$ 5.74USD$ 5.66USD$ 5.58USD$ 5.47
 
Frequency::
Qty:
pieces
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
 
  • Overview

Specifications:


  • Nominal Voltage: DC3-12V
  • Operating Current: 150mA 9V
  • Operating Frequency: 315MHz/433MHz
  • Means of Communication: Single
  • Modulation Rate: 10KHZ
  • Modulation: ASK (Amplitude Limit)
  • Operating Temperature: -10 ℃ - +60 ℃
  • Input Signal: TTL level
  • Radiated Power: 1mW 9V
  • Transmission Distance: 3000 Meters
  • Color: Green

Features:


  • The transmitter module is of tiny design for convenient use
  • Perfect for any wireless control application
  • Small size and medium-power design to the transmitter module
  • To install simply follow the simple wiring diagram

Details:



  • Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000

    The wireless transmitter module is of tiny design for convenient use





  • Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000

    The transmitter board module is with low consumption, provides great performance





Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000




  • Delicate in details, with great workmanship, the wireless transmitter module is reliable for long time use

  • Made of high quality material, the wireless transmitter module provides great durability

How to Build a Wireless Remote Control:

Zrabra 3000M Wireless Remote Control Transmitter Board Module TX-3000


Simple wireless devices use various components to activate an infra-red signal that broadcasts to a receiver box, allowing the user to program the control. Basic wireless remote controls simply turn a device on or off. Components used in a wireless device can be found at most electronics outlets and hobby shops. Specialized retail establishments have pre-packaged kits that can be used by a beginner. At the very least, even experienced electronics enthusiasts use pre-made remote control boxes due to the simplicity of their design, including ergonomic support. The structure of the wireless remote control provides a builder with not only knowledge but the reasons a receiver can be controlled by the device


  • Open the remote control housing and place a push button switch on the side. In the upper right corner of the housing, fasten a 3-volt battery holder. Be sure enough room is available to install and remove the battery
  • Run a wire from the push button switch and link to the 3-volt battery holder at the negative connection. Attach another wire to the push button switch and lead it to the Meg 1/4W resistor and the NPN silicon transistor. Run a third wire from the Meg 1/4W resistor and attach it to the 22K 1/4W resistor and and the PNP silicon transistor
  • Position the infra-red LED on the front of the housing. Attach the LED and run wires to both transistors. From the 22K 1/4W resistor, run a wire to the C220.01uF 16v ceramic disk capacitor. Run another wire between the NPN silicon transistor and the ceramic disk capacitor
  • From the positive connector on the 3-volt battery holder, connect a wire to the PNP silicon transistor. This will allow for proper current flow in a closed circuit. Ensure the push button switch is positioned to "off" and place a 3-volt battery into the holder. Close the remote control housing
  • Point the remote control at a receiver, making sure the LED on the control is aimed at the LED of the receiver. Push the button and the receiver should power on and off. To adjust the receiver to be programmed, point the remote control and hold down the push button switch. Adjust the pot or taper on the receiver

Package Included:


  • 1 x Transmitter Module