Home >> Security & Surveillance >> Home Alarm >> Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A

Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A

SKU:A1485000FE

Welcome to this page! The Wireless Remote Control Module gives you full control over the garage door.The Transmitter Board Module is small size, wide operating voltage range (3V-12V), high emission power, low power consumption, widely used in the sum...
Retail Price:
USD$ 3.37
Wholesale Price:
 
Wholesale Price
Quantity 2-78-1920-49≥50
Price USD$ 2.83USD$ 2.75USD$ 2.67USD$ 2.56
 
Frequency::
Qty:
pieces
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
 
  • Overview

 Specifications:


  • Operating Voltage: 3V-12V
  • Operating Current: Max ≤ 45mA (12V), min ≤ 2mA (3V)
  • Resonant: SAW resonator (SAW)
  • Modulation: ASK / OOK
  • Operating Frequency: 315MHz/433.92MHz(optional)
  • Frequency Error: ± 150kHz (max)
  • Transmission Power: 50mw
  • Transmission Rate: ≤ 10Kbps
  • Transmission Distance: 315M
  • Size: 17 x 14mm/0.67 x 0.55in

Features:


  • Long-distance wireless remote control
  • This Transmitter Board Module can be used in all kinds of anti-theft alarm system
  • This Wireless Remote Control Board can be used in a variety of low-rate digital signal for wireless transmission
  • This Wireless Remote Control Module can be used in all kinds of household electrical appliances, smart toys, remote control and so on

Details:

Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A


  • Overall of Wireless Remote Control Transmitter
  • The Transmitter Board Module is small size, wide operating voltage range (3V-12V), high emission power, low power consumption, widely used in the summary data wireless transmission, wireless remote control, burglar alarm and other occasions

Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A


  • This Transmitter Board Module can be used in all kinds of anti-theft alarm system, also can be used in a variety of low-rate digital signal for wireless transmission

Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A


  • This Wireless Remote Control Switch is a low cost. This Transmitter Board Module is with high quality, can last long time

Size in Detail:

Zrabra 315MHz/433.92MHz Wireless Remote Control Transmitter Board Module TDL9906A


How to Build a Wireless Remote Control


  • Simple wireless devices use various components to activate an infra-red signal that broadcasts to a receiver box, allowing the user to program the control. Basic wireless remote controls simply turn a device on or off. Components used in a wireless device can be found at most electronics outlets and hobby shops. Specialized retail establishments have pre-packaged kits that can be used by a beginner. At the very least, even experienced electronics enthusiasts use pre-made remote control boxes due to the simplicity of their design, including ergonomic support. The structure of the wireless remote control provides a builder with not only knowledge but the reasons a receiver can be controlled by the device

Instructions:


  • Open the remote control housing and place a push button switch on the side. In the upper right corner of the housing, fasten a 3-volt battery holder. Be sure enough room is available to install and remove the battery
  • Run a wire from the push button switch and link to the 3-volt battery holder at the negative connection. Attach another wire to the push button switch and lead it to the Meg 1/4W resistor and the NPN silicon transistor. Run a third wire from the Meg 1/4W resistor and attach it to the 22K 1/4W resistor and and the PNP silicon transistor
  • Position the infra-red LED on the front of the housing. Attach the LED and run wires to both transistors. From the 22K 1/4W resistor, run a wire to the C220.01uF 16v ceramic disk capacitor. Run another wire between the NPN silicon transistor and the ceramic disk capacitor
  • From the positive connector on the 3-volt battery holder, connect a wire to the PNP silicon transistor. This will allow for proper current flow in a closed circuit. Ensure the push button switch is positioned to "off" and place a 3-volt battery into the holder. Close the remote control housing
  • Point the remote control at a receiver, making sure the LED on the control is aimed at the LED of the receiver. Push the button and the receiver should power on and off. To adjust the receiver to be programmed, point the remote control and hold down the push button switch. Adjust the pot or taper on the receive

Package Included:


  • 1 x Wireless Transmitter Board Module