Home >> Electronics >> Gadgets >> Test Equipment >> Fixed Telephone Signal Lightning Protector Arrester Device OVP-RJ11-TELE-2-C

Fixed Telephone Signal Lightning Protector Arrester Device OVP-RJ11-TELE-2-C


The signal protector uses multi-level protection circuit, metal casing, the sealing is good, and with dust-proof anti-corrosion features. Installed between the protected device and outside line. imported high-speed protection device, which has fast r...
Retail Price:
USD$ 65.54
Wholesale Price:
Wholesale Price
Quantity 2-45-910-29≥30
Price USD$ 50.46USD$ 47.99USD$ 45.52USD$ 42.22
TV Standard:
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
  • Overview


  • Rated Voltage Un: 160V
  • Maximum Sustainable Operating Voltage Uc: 184V
  • Nominal Discharge Current(8/20μs) In: 350A(line/line); 5KA(line/ground)
  • Maximum Discharge Current(8/20μs) Imax: 10KA
  • Voltage Protection Level @ In UP: ≤330V(line/line); ≤600V(line/ground)
  • Transfer Rate(3dB) fg: >2MHz
  • Interface Type : RJ11
  • Protected Lines: 3,4
  • Enclosure Material: Aluminum
  • Insertion Loss IL: <0.2db
  • Series Resistance R: 10Ω SPD
  • Uses multi-level protection circuit, imported high-speed protection device
  • It has fast response, low output residual voltage, superior transmission
  • Metal casing, the sealing is good, and with dust-proof anti-corrosion features
  • Uses series connected way
  • Installed between the protected device and outside line


Fixed Telephone Signal Lightning Protector Arrester Device OVP-RJ11-TELE-2-C


  • The product is connected in serial way, install the lightning protection devices between the protected device and outside line with the corresponding interface
  • The components are subjected by stringent testing, general speaking, it's without special maintenance. When you operate fault detection, remove it, measure the resistance. if it's normal. The resistance between the input and output should be ≤12Ω, the wire-to-ground resistance is ≥10ΜΩ. If the measured data does not meet the above requirements, showing that there is some wrong in it, which shall be replaced promptly
  • The protector needs a good grounding, lightning ground wire should be short, thick, straight at most, grounding resistance should be meet with national standards

How to Connect a Cable to a Monster Surge Protector:

  • Monster Cable makes several types of surge protectors, ranging from simple power strips to full-blown entertainment PowerCenters. Whichever model you have, the procedure for connecting your cables is similar. Since surge protectors are useless when plugged into ungrounded wall outlets, verify that your wall outlet is wired properly before attaching your audio and video components to the surge protector; if you're not sure that your home's wiring is up to snuff, Monster recommends asking an electrician to take a look at it.


  • Verify that all satellite dishes, television and radio antennas, and other rooftop devices you will connect to your Monster surge protector are properly grounded. (Check with the devices' manufacturers to find out how to determine this.) Doing so will help prevent voltage surges from compromising your surge protector and possibly damaging your audio and video components
  • Choose a three-pronged (grounding) outlet far away from potential foot-traffic problems. Behind your home entertainment system or in a corner is best
  • Plug each of your audio and video components into its recommended outlet on the surge protector: Monster surge protectors have different types of outlets for different components. This allows the surge protector to "clean" the signal for each type of component so as to minimize static and interference. Reference the Monster manual for your particular surge protector if there's any doubt
  • Plug coaxial cables into the proper outlets. For example, connect your satellite's coaxial cable to the "Satellite In" outlet. Then connect the "Satellite Out" coaxial cable to your TV or cable box. Do the same for any other types of communication cables you have, such as phone or Ethernet. Depending upon your setup, purchase additional cables if necessary
  • Plug your Monster surge protector into the wall grounding outlet after connecting all your components.
  • Turn the surge protector on with its power switch

Package Included:

  • 1 x Fixed Telephone Signal Protector