Home >> Toys & Hobbies >> Radio Control >> RC Helicopters & Accessories >> Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs

Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs

SKU:A1560000BG

This is a brand new MYSTERY 260mm Square Corner Carbon Fiber Main Blades A Versin for WALKERA 22E series RC Helicopter.This 260mm Main Blades is very easy to repair, and will give good tracking for your WALKERA 22E series RC Helicopter. Blades o...
Retail Price:
USD$ 29.04
Wholesale Price:
 
Wholesale Price
Quantity 2-56-1415-39≥40
Price USD$ 19.75USD$ 17.58USD$ 15.40USD$ 12.50
 
Qty:
pieces
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
 
  • Overview

Specifications:


  • High quality square corner carbon fibre main blades
  • The Carbon Fiber Main Blades are easy to repair
  • Newest development from WALKERA with high quality carbon fiber main blade
  • These 260mm Main Blades will give good tracking for your WALKERA 22E series RC helicopter
  • Size: 260mm /10.24in(L)
  • Material: Carbon fiber

Details:

Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs

Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs


  • This is a MYSTERY 260mm Square Corner Carbon Fibre Main Blades A Versin for WALKERA 22E series RC Helicopter

Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs

Mystery MYSTERY 260mm Carbon Fiber Main Blades (A) for WALKERA 22E Series RC Helicopter 2 Pcs


  • It is very easy to repair, and will give good tracking for your WALKERA 22E series RC Helicopter

How to Balance RC Helicopter Blades:


  • Place the rotor blade on top of a dowel rod or other round surface to balance it. Balance the blades evenly from right to left to find the center of gravity. The center of gravity is the point at which the blade is evenly off the ground on both sides while perfectly balanced on the rod
  • Place a colored piece of tape on the line for center of gravity or CG. You can remove the center of gravity mark later by removing the tape or markings with nail polish remover. Repeat the step for the second rotor blade
  • Face the rotor blades in opposite directions and lay one on top the other. Match up the bolt holes and slide a bolt through. Check the center of gravity marks on each blade to see if they line up. If the marks line up, the balancing is complete. Proceed to Step 4 if the blades aren't balanced
  • Weigh the blades to determine how far off balance they are. Anything more than 2/10-gram off from each other will cause problems. If the blades are out of balance by more than 2/10-gram consider sending them back to the manufacturer
  • Place a bolt through the rotor blade holes to attach them as one unit. Place two 18-inch lengths of 2-by-4 lumber side by side. Balance both ends of the bolt atop the lumber so that the blades are supported and can freely move between the blocks
  • Place a piece of tape in the center of the blade that is lighter. The lighter blade will be the one higher in the air. Place more tape on the lighter blade at the center of gravity until the blades become balanced. Try to use long lengths of tape to minimize the amount of tape used

Package Included:


  • 2 x Carbon Fibre Main Blades