Home >> Security & Surveillance >> Surveillance Accessories >> Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w

SKU:A1217000CP

Do you want to see movies or other programs in your other room without moving your TV from the living room? Do you want to choose a good transmitter and receiver? What you are viewing is the 2.4GHz Channel 4 100m wireless receiver & transmitter k...
Retail Price:
USD$ 350.78
Wholesale Price:
 
Wholesale Price
Quantity 2-45-910-29≥30
Price USD$ 134.14USD$ 128.96USD$ 123.78USD$ 116.86
 
Qty:
pieces
If you want to buy only 1 piece, please alter the quantity in ‘My Cart’.
Note: you could enjoy the wholesale price of this item as long as the item quantity of your order is more than 1.
  • For online wholesaler or distributor, you can buy directly online. If you want to buy more than offered quantities for better price, please click wholesale inquiry.

  • Top Selling
 
  • Overview

Specifications:


Transmitter:


  • Transmitting Frequency: 2.414GHz; 2.432GHz; 2.450GHz; 2.468GHz
  • Number of Channels: 4 Channels
  • A/V Mod Method: FM
  • RF Power: Model A: 20mW; Model B: 100mW; Model C: 1W
  • Input: Video Out + R/L Audio In
  • Power: DC 9V/Model A & B: 220mA, Model C: 350mA
  • Operating Temperature: -10℃-50℃(14F-122F)

Receiver:


  • Number of Channels: 4 Channels
  • A/V Method: FM
  • Output: Video Out + R/L Audio In
  • Power: DC 9V.180mA
  • Operating Temperature: -10℃-50℃(14F-122F)

 Features:


  • This machine sound, video signal adopts the microwave transmission means with extremely high frequency
  • Its signal carrier frequency is up to 2.4GHz
  • High transmission frequency can prevent 900 MHz frequency channel crowded to capacity radio telephone interference of signal from effectively extremely
  • The great degree prevents a machine from transmitting frequency to other interference of receiving the equipment too at the same time
  • Performance is superior to 900MHz 1.2G picture transmitting device greatly
  • In order to guarantee the receiving clearly of the sound and picture, have also had 4 channels available on the plane
  • Adopt frequency modulation way that have an advantage over amplitude modulation way of
  • Sending the sound source of CD, the stereo result is remarkable, the tone quality is excellent

Details:


Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  •  This is a brand new wireless receiver and transmitter with 2.4G 4 channels and 3W A/V transmitter of 3 models

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • This FM transmitter and receiver effectively solve the family problems of sharing audio-visual equipment

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • The wireless transmitter and receiver offers fine audio and video receive quality for DVD, CD, TV, security CCTV signal source

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • There is a long cable attached with this transmitter and receiver 

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • With this transmitter and receiver, you can watch the cable TV and satellite TV at the same time

How to Build a RF Transmitter Receiver?


Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • Radio frequencies constantly saturate the air around us, carrying signals that broadcast music, information and controls for electronics and toys. You can build a simple receiver that will pick up the signal coming from a radio frequency, or RF, transmitter. Otherwise known as a radio, the receiver consists of a few simple parts, some of which can be found around your own home. With some trial and error, you can develop an RF receiver that will be tuned in to the transmitters and broadcast signals of your choice

Instructions


  • Punch four holes in the side of your sturdy plastic bottle, such as a shampoo bottle, with a nail. There will be two sets, one located near the top and one near the bottom. The holes in each set will be spaced about a half-inch apart running parallel to the top and bottom of the bottle
  • Thread one end of your magnet wire through the top two holes and pull about 8 inches through
  • Wind the long end of the wire tightly around the bottle, making sure each wrap touches the wind before it. After every five winds of the wire, wrap a small loop around a pencil or pen so that you will have a series of small loops that stand out from the other windings. These are called wire taps (see reference 1). Continue winding in this pattern until you reach the bottom of the bottle. Remove the pen or pencil from the smaller windings
  • Thread the end of the wire through the holes punched in the bottom of the bottle. Use wire cutters or a sharp knife to strip both free ends of the wire as well as the wire taps of vinyl coating to reveal the bare magnet wire underneath. Do not strip any coating from the wire wrapped around the bottle
  • Solder a Germanium diode to the wire end at the bottom of the bottle
  • Cut and strip off one end of a telephone cord to reveal the four inner wires. Locate the yellow and blue wires---the wires that are used to transmit the audio signal in the handset---and solder one to the free end of the Germanium diode. Wire the other to the wire end at the top of the bottle. The color wire you attach to each end will not matter, as you are simply completing a circuit. Connect the uncut end of the cord to a telephone handset
  • Ground the radio receiver by clipping an alligator jumper to a bare portion of the wire coming from the top of the bottle. Clip the free end to a solid piece of metal with a good connection to the earth, such as a pipe
  • Clip one end of an alligator jumper to between 50 feet and 100 feet of standard insulated wire. This will act as an antenna. Connect the free end of this jumper to one of the bare coil taps on the bottle. You should now be able to hear radio stations coming through the telephone handset. The coil tap the jumper is connected to will determine the station. You may need to adjust the antenna or string it to a high point such as a tree branch to get a clear signal

Tips & Warnings


  • The size and spacing of the taps, as well as the antenna position, will determine the frequencies this RF receiver will be able to pick up. Experiment with these elements to tune your radio further. With some trial and error you should be able to pick up a signal from a homemade transmitter

How to Bind Your Transmitter to Your Receiver?

Wireless 2.4G 4 Channels Transmitter and Receiver System ESPT3w


  • The receiver translates radio signals broadcast by the transmitter into mechanical impulses that are used to drive your radio-controlled (RC) vehicle. Communication between these two electronic devices is essential for a well-functioning RC. A wireless connection is established between the transmitter and receiver during a process called binding. Learning how to bind your radio system's components will ensure you maintain optimum control over your vehicle

Instructions


  • Plug the battery into the receiver, then look for the setup button on the front face of the receiver
  • Press and hold the receiver button while turning on the power. Press and hold the link button on the transmitter while you turn on the power
  • Wait for the status LED on both the transmitter and receiver to turn a solid green color, indicating the binding was successful

Package Included:


  • 1 x Wireless 2.4G AV Receiver
  • 1 x 4CH 3W Wireless AV Transmitter
  • 1 x Outdoor Amplifier
  • 1 x Outdoor Amplifier Antenna
  • 1 x User Manual