Home >> Toys & Hobbies >> Electronic, Battery & Wind-Up >> Electronic, Interactive >> THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy

SKU:A0135000FE

What you are viewing is a Mcdull ABS Resin Solar Powered Toy, if you want to have something to decorate you car or desk, this cute ABS resin solar power toy will be a smart choice!Made of high quality material, the ABS resin solar power toy is d...
Retail Price:
USD$ 27.98
Wholesale Price:
 
Wholesale Price
Quantity 2-78-1920-49≥50
Price USD$ 8.12USD$ 7.55USD$ 6.98USD$ 6.22
 
  • Top Selling
 
  • Overview

Specifications:


  • This cute cartoon figure toy is solar energy powered and does not need battery
  • It is gently shaking when sunlight or other light energy source is directed
  • This ABS resin solar power toy is solar powered
  • It will give you back your good mood when you look at them
  • Put one on your desk, your windowsill or your car and you will be unable to suppress a grin every time it begin to sway
  • The ABS resin solar power toy will give you back your good mood when you look at them
  • Place it near light source or sunlight and this Mcdull toy will moving its head & feet automatically
  • This solar power Mcdull will be a great gift idea for anyone
  • Material: ABS Resin
  • Size: 85 x 75 x 90mm/3.3 x 3.0 x 3.5in(L x W x H)

Details:

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy


  • A most lovely ABS resin solar power toy for people at all ages as well as a decoration to your house

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy


  • This solar power toy is made of high quality material that ensures durability. Best choice for you

Size in Detail:

THTS Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy


NOTE:


  • Suitable for above 6 years old children
  • It can not be washed, please wipe it with a soft cloth lightly

How to Build a Solar-Powered Toy Car:

Make the Car Body:


  • Cut the wood board slightly larger than the plastic bottle that you are using for the car body. This will act as the body platform. Foam board could be used here just as well but wood holds up better
  • Cut two small sections of foam board to the same width as the body platform and about 2 inches in length. Glue these reinforcing blocks to the top and bottom edge of the body platform. Use a ruler to mark a dot on each of the reinforcing blocks that's 1 inch from the front and the side. There'll be four dots total
  • Screw in a screw eye in each dot. Make sure the two eyes per axle are approximately the same height off the board
  • Use the dowel rods as axle material. Measure the axle material so that the wheels will be approximately 1 inch outside of the platform on each side. With a saw, cut the two dowel rods and use sandpaper to sand the tips so that they fit the wheels tightly
  • Attach one wheel to the axle then slip the axle through the screw eyes before attaching the second wheel. The fit between wheel and axle must be tight. On the front axle, put the large pulley on the axle between the platform body and the right wheel. Make sure the wheels on one axle match and the wheels on the second axle match

Make the Car Engine:


  • Put the motor into the motor clip and attach the small pulley to the motor's shaft. Place the rubber band around the large pulley and the small pulley and use the tautness of the rubber band to indicate where you glue the motor clip onto the platform body. The rubber band must be taunt but not overstretched
  • Remove the rubber band and glue the motor clip on the body platform near the right front wheel. Make sure the engine wire's still available for attachment
  • Thread the rubber band back onto the motor pulley and the drive pulley
  • Drill a hole through the top and bottom of the plastic bottle. Run the wire through the holes. Glue the bottle to the platform
  • Connect the engine wires to the solar panel wires. Attach the solar panel to the top of the bottle with glue. If you wanted an angled solar panel, make it out of an additional piece of foam board and small blocks. Then attach the angled platform to the bottle, then the solar panel to the platform. Tape any loose wires onto the car body so that they don't drag on the floor 

Package Included:


  • 1 x Cute Mcdull Moving Head & Feet ABS Resin Solar Power Toy